We do have an option that'll work for you! To replace your key, you are just going to need the:
-Replacement Key for Bauer RV Lock # BA52RR.
This is the direct replacement for your existing Bauer key number 954. view full answer...
To install the new slide out seals like the Rubber Bulb Seal for RV Slide Out - 1-3/16" C-Channel # SR57FR, you will need to pulled off the and scraped clean.
After the old seal is pulled off and the old residue has been cleaned off, you'll then just need to install the new seal.
To pick put the new slide out seal for your trailer, you will need to remove a portion and take some measurements of your current seal, and see how it attaches.
If you are able to take some measurements, and... view full answer...
You will need to determine what spindles you have on your trailer axle. I've attached a photo along with locations to measure your spindle for proper fit using a caliper like # PTW80157 for best accuracy. You can also pull the bearings and get the numbers off the face of the inner and outer bearing to determine what brake hub will be a good fit. If there is not a brake flange on your axle, one will need to be welded on.
Let me know what you've got and I'll be happy to assist with... view full answer...
The closest sink I was able to find to what you're needing is the Better Bath RV Kitchen Sink # LC92ZR.
This sink measures 25" long x 17" wide x 6-7/8" tall making this 1/4" longer and 2-1/2" less wide, has an interior measurement of 22" long x 14-1/8" wide x 5-3/4" tall, and is grey in color.
I have attached a product review as well as a dimensional diagram for you to check out as well. view full answer...
Well you're right, that's not normal. What likely happened is that you may have just got a defective unit and it'll just need to be replaced.
I recommend checking out the Lend-a-Hand Extra Large Folding Grab Handle for RVs # AM-533.
This replacement handle is virtually the same as the Camco Fold-Away RV Grab Handle # CAM42175, only this is going to be made in the USA with better quality materials, is a bit larger at 37" tall x 25-1/2" wide, and is also made from powder coated Aluminum... view full answer...
I do have a solution for you to use a cargo carrier on your Jayco TT but unfortunately all of our cargo carriers are for use with trailer hitch receivers.
If you would like to go ahead and install a trailer hitch then I recommend going with Curt # C13701 or # C13702. These are compatible with trailer frames that are 18" - 51" wide, they have a 2" receiver, and are rated for 500 lbs of tongue weight. The only difference between these 2 options is that the former has a 2" drop whereas the... view full answer...
The closest cap we have that matches your measurement is the Replacement Phoenix USA Rear Wheel Center Cap - 6-1/2" or 8-1/4" Hub Diameter # PXPH1764. This comes with a 6-1/2 center cap requirement. It is also made specifically for a 10-bolt pattern with 285mm bolts. view full answer...
The sway control ball on the Replacement Weight Distribution Bolt-Together Round Bar Head # PS58442 can be used with two balls and you can use the balls on either side of the head assembly (see picture).
This replacement head fits Pro Series weight distribution systems # PS49583, # PS49582, # PS49901
The adjustable shank # C17100 is not included with this product, but it does come with the bolts, the nuts and the washers to get that installed and attached to the weight distribution shank.... view full answer...
Since the 12V RV LED Puck Light - Surface Mount - 3" Diameter # 328-K-1003WS has unremovable LED lights, there isn't going to be any replacement bulbs. So, when it comes time to replace the light, you'd have to replace the entire light assembly.
The good news is most standard LED lights will last 50,000 hours, so it's going to be a while before you'd have to swap them out. view full answer...
Go To Results